• Brand: Mopar

• Part Numbers: 68157291AA, 68436631AA, 05083285AA (MO-291, MO-631, MO-285AA)

• SKU: B4L1015AWW

• Weight: 1.02 pounds

• Dimensions: 10.08 x 4.84 x 4.49 inches

• Product Grade: Performance Part

WHAT’S INCLUDED

• 1x Mopar 68157291AA Fuel Filter for 6.7L Cummins engine

• 1x Mopar 68436631AA Fuel Filter for 6.7L Cummins engine

• 1x Mopar 05083285AA Oil Filter for 6.7L Cummins engine

GUIDE TO CHANGING OIL AND FUEL FILTERS ON YOUR RAM 6.7L CUMMINS

Regular maintenance is essential for optimal performance of your RAM 6.7L Cummins engine. This guide outlines how to change your fuel and oil filters using Mopar parts.

TOOLS AND SUPPLIES NEEDED

For Oil Change:

• New engine oil (refer to your owner’s manual for specifications)

• New oil filter: Mopar 05083285AA

• Oil filter wrench

• Socket set and ratchet

• Oil drain pan

• Funnel

• Jack and jack stands (if necessary)

• Gloves and rags

For Fuel Filter Change:

• New fuel filters:

  • Mopar 68157291AA (Primary)

  • Mopar 68436631AA (Secondary)

• Fuel filter wrench (if needed)

• Socket set and ratchet

• Safety glasses and gloves

• Rags

OIL FILTER REPLACEMENT STEPS

1. Prepare Your Vehicle:

   • Park on a level surface and engage the parking brake.

   • Lift the vehicle if necessary, using a jack and securing with jack stands.

2. Drain the Old Oil:

   • Locate the oil drain plug beneath the vehicle.

   • Position the oil drain pan underneath.

   • Remove the drain plug and let the oil drain completely.

3. Remove the Old Oil Filter:

   • Locate the oil filter on the engine block.

   • Use the oil filter wrench to unscrew it, allowing any residual oil to spill into the pan.

4. Install the New Oil Filter:

   • Apply a small amount of new oil to the rubber gasket of the new filter.

   • Screw the new filter into place by hand, tightening until snug.

5. Replace the Oil Drain Plug:

   • Clean the drain plug and reinstall it securely.

6. Add New Oil:

   • Open the hood, remove the oil filler cap, and pour in the new oil using a funnel.

   • Replace the oil filler cap once done.

7. Check the Oil Level:

   • Wait a few minutes, then check the oil level with the dipstick. Add more oil if necessary.

8. Lower the Vehicle and Check for Leaks:

   • Remove jack stands and lower the vehicle.

   • Start the engine and check for leaks underneath.

FUEL FILTER REPLACEMENT STEPS

1. Prepare Your Vehicle:

   • Ensure safety by parking on a level surface and engaging the parking brake. Lift the truck if necessary.

2. Relieve Fuel System Pressure:

   • Locate the fuel pump fuse/relay and remove it.

   • Start the engine and let it stall to relieve pressure.

3. Remove the Old Fuel Filters:

   • Locate the primary and secondary fuel filters.

   • Disconnect fuel lines carefully, catching any spills with rags.

   • Use a fuel filter wrench to remove both filters.

4. Install the New Fuel Filters:

   • Position the new filters correctly, ensuring the flow direction matches the markings.

   • Reconnect the fuel lines securely.

5. Reinstall the Fuel Pump Fuse/Relay:

   • Replace the fuse or relay that was removed.

6. Check for Leaks:

   • Turn the ignition to the "On" position without starting the engine to pressurize the system.

   • Inspect for leaks around the new filters.

7. Lower the Vehicle (if lifted):

   • Carefully lower the vehicle if it was elevated.

FINAL STEPS

• Dispose of Old Oil and Filters: Take used oil and filters to a recycling center or an auto parts store that accepts them.

• Record Maintenance: Document the filter and oil changes for your records.

Note: Always refer to your RAM’s service manual for specific instructions and part numbers. If unsure about the process, consult a professional mechanic.